Windigipet 2012 and intelligent train number in silulation mode.
 

Windigipet 2012 and intelligent train number in silulation mode.

Begonnen von ebarra, 16. Mai 2013, 22:53:31

Vorheriges Thema - Nächstes Thema

ebarra

Hi,
Does the loco speed reflects the ramp down speed we should get when using intelligent train  numbers in simulation mode With the desk top version?

Regards.
  • Win-Digipet-Version:
    2015
  • Anlagenkonfiguration:
    Intellibox and simultaneous 2 and 3 rails.

ebarra

I guess I have to refresh my question:
Basically : I could not get the desired effect of speed degressing when using the intelligent train number display.
I still obtain the speeds steps of standard train numbers.
Any tricks to activate it?
Shall we also get it in simulation mode?
Regards.
  • Win-Digipet-Version:
    2015
  • Anlagenkonfiguration:
    Intellibox and simultaneous 2 and 3 rails.

Stefan Lersch

Hi,

have you altered your existing route? The end point should be "at the signal" or "at the end of the platform" or whatever it is called in English. I guess it still says "at the contact" and in this case it behaves as if there is no intelligent train number display.

I haven't tried this during simulation so I can't answer that.
Viele Grüße,
Stefan
  • Win-Digipet-Version:
    WDP 2021.x Beta
  • Anlagenkonfiguration:
    N-Anlage im Bau, Minitrix & Co., Tams MC 2.2.3, DCC
  • Rechnerkonfiguration:
    Quad Core 8 GB mit Win 10, 32"quot Bildschirm

ebarra

Dear stefan,
Thanks for your help.
My route belives same as before if it is what you consider not altered.
I tryed to use the intelligent train number the following way:
i took a loco alone :length 30 cm!
i combibed in the travel order 4 zones cumulating approx 4 meters and asked the loco (train) to stop at middle of platform but the machine stops at the braking contact as with standard train number.
Regards.
  • Win-Digipet-Version:
    2015
  • Anlagenkonfiguration:
    Intellibox and simultaneous 2 and 3 rails.

Stefan Lersch

Hello,

you need to do 2 things: a) creating the intelligent train number display (iTND) (what you did) and b) alter the route to this iTND. If you do not both the train will not stop where you want it to. Please read again what I wrote above.
Viele Grüße,
Stefan
  • Win-Digipet-Version:
    WDP 2021.x Beta
  • Anlagenkonfiguration:
    N-Anlage im Bau, Minitrix & Co., Tams MC 2.2.3, DCC
  • Rechnerkonfiguration:
    Quad Core 8 GB mit Win 10, 32"quot Bildschirm

ebarra

  • Win-Digipet-Version:
    2015
  • Anlagenkonfiguration:
    Intellibox and simultaneous 2 and 3 rails.

Stefan Lersch

Open the route editor. Select the route to the iTND. Select the tab  "Start/Stop/Destination". At the bottom you see the field "Dest." that indicates the contact and after it should be a field that says "Stop at contact". Change this to "Stop at stop position". See attachment.
Viele Grüße,
Stefan
  • Win-Digipet-Version:
    WDP 2021.x Beta
  • Anlagenkonfiguration:
    N-Anlage im Bau, Minitrix & Co., Tams MC 2.2.3, DCC
  • Rechnerkonfiguration:
    Quad Core 8 GB mit Win 10, 32"quot Bildschirm

ebarra

Stefan,
Understood (finally).
Thanks a lot for your time.
Regards.
  • Win-Digipet-Version:
    2015
  • Anlagenkonfiguration:
    Intellibox and simultaneous 2 and 3 rails.