Märklin Transfer Table

[dconner]

Dear WDP Experts,
I need help with my Märklin Transfer Table problem. I have introduced the transfer table into my WDP layout plan with FB 901 placed at both sides where both rail connections line-up together. When I check the routes in Route Editor with Check Route-record I get the fatal error "2 Invalid track symbols" from these two transfer table connections - 901.
Can someone please help me ?

[dconner]

Here is an update from my Märklin Transfer Table / WDP ver.12.1 problem:-

[dconner]

Here is an update on my Märklin Transfer Table / WDP 12.1 problem. I have not yet resolved the Routes Editor error, but have found a fault in the documentaion regarding the Virtual Solenoid activation. I have found the error in the following:-
  WDP Handbuch Version 2009,
  WDP 12.1 softare English Edition, but not in the German software version, WDP 12.2.
The error concerns the activation of the Virtual Solenoid (Virtueller Magnetartikel).
I think I'm correct in saying that the 901-909 devices must not be termed a Virtual Solenoid I deactivated the tick (HAKEN) in my layout and the Transfer Table is now responding correctly to the WDP software commands. The Routes Editor problem is still there though.

Have a great weekend. Regards, David CONNER.

[dconner]

I'm still trying to get this fault with my transfer table corrected. In the HELP section of version12.1, 15.1 General, it states:-
 "Before using the transfer table, the transfer table should be activated in the system settings on the index card ""Program settings - General """.

Is this a case of the HELP file being out of date, or the software missing something ?. In my version is does not have this transfer table activation possibility.

Gruß / Regards  Dave CONNER.

[Stefan Lersch]

Hello Dave,

I'm a little bit lost. Do you have two or one problem concerning the invalid track symbols? There's now the free update 12.2 English. Did you install it?

[dconner]

Lieber Stefan,
Appologies if I have confussed you, my problem is still with the Route Editor, activating the Check Route-record I get the fatal error "2 Invalid track symbols". Todays previous entry was posed as a question to a possible solution to my problem "...fatal error 2 Invalid track symbols".

Many thanks for your interest. Dave CONNER

[dconner]

Lieber Stefan, I forgot to add that I'm using version 12.2 English update. Please convey my personal thanks to the update team of WDP.

Gruß, Dave CONNER.

[Stefan Lersch]

Lieber Dave,

I think you once changed 2 symbols in your track diagram. These are those invalid track symbold. Check which routes are infected and restart the route recording. Don't delete those routes but change them. Therefore click on the camera symbol and then in the layout click on the wrong symbols. Save your changes. You're done.

[dconner]

Lieber Stefan,
Many thanks for your help and advice, you certainly have given me something to think about. I will get back to you within the next few days with a new status report.
Vielen Dank !
Viele Grüße-Dave Conner

[dconner]

Lieber Stefan, I still have this error 2 problem. What ever I try, the route that includes 901 on the transfer table is always blocked. I have deleted these Feed Back's, that is 901 and the error is corrected. When 901 is again introduced, the error returns.

Viele Grüße-Dave CONNER

[dconner]

Lieber Stefan, error 2 should read :- the route contains two invalid track symbols. That is at 901.

Viele Grüße Dave Conner

[dconner]

Lieber Stefan, Of course I still have my Märklin Transfer Table (Schiebubühne) - WinDigipet problem. Is there a possibility that you and or Markus Herzog could send me a WinDigipet Zip plan with a functioning Transfer Table and Drehscheibe ?(  dconner@01019freenet.de ).
Thanking you in advance- Frohe Festtage und einen guten Rutsch ins neue Jahr.

Gruß- Dave CONNER

[dconner]

 Dear all WDP users, Bernd Senger has found that I'm not using a Schiebebüne (Transfer Table) from Boll as detailed in Workshop 24, I never got WS 17. Thanks to Bernd I'm now on the right road.