New conditions in tour automatic editor

[ebarra]

Hi,
Few questions regarding  new conditions in tour automatic editor:
a) Vehicule position in train:
how Windigipet can know which train number display we are looking at?
See picture attached. no train number display to enter?

b) Same thing with "Only if loc with direction" . Here also we do not enter any C-N number?
How can we and Windigipet know which train number display we are looking at?
Weird, can someone explain?

Thanks
Eric.

[Markus Herzog]

Hi Eric,

regarding Vehicle position in train:
We are asking for the position of a specific vehicle in the train where this vehicle belongs to.

Drag a locomotive from the loco bar/loco control/locomotive monitor or a waggon from the waggon monitor to the textbox currently showing a zero in the picture and then you will see that you can monitor the position of this vehicle in its train.

Regarding "Only if loc with direction":
This condition just monitors the direction of the loco using the current tour automatic row. There is a similar condition in the sub menu ...train number display where you can check for the locomotive direction on a specific train number display.

Regards
Markus

P.S.: Seems as 2018 has already arrived at your place? Have you already installed update 2018.0b?

[ebarra]

Markus,
Thanks nks for your reply.
What i am trying to achieve, is to lnow if a train on a given train number display in in push or pull mode?
Any idea how to do it?
Many thanks.
Eric.

[ebarra]

Dear Markus,
I missed your question when reading your answer first time: 2018 welle received and update installed. 2015 on its way back to you.
Many thanks.
Regards.

[ebarra]

Hi everyone,
I guess this question might be for Markus  as involved in the development:
Basically , I have unconsistency with the Loco type on TDN as shown on the PDF attached.
I hope it is clear enough.
Let me know if it is not.

Thanks in advance.
Regards.

[Markus Herzog]

Hi Eric,

The condition does not refer to the decoder direction. But to driving direction...and then the loco is the first vehicle in driving direction. You need to set not “against driving direction” but the opposite selection.

Regards
Markus

[ebarra]

Hello Markus,
I did set both cases in my example. Crystal clear for me.
What is wrong is the fact that I get a green condition when checking a loco type which is not on the TDN???
The loc on TDN 21 is of “manoeuvre “type” and this work. But the “vapeur” type is not and cannot be in same time than the manoeuvre type on the TDN 21. Then I get a green with vapeur type when it should not be.
Do you get my point?
Regards.

[Markus Herzog]

Hi Eric,

Please provide me a backup of the project with this situation. Then I will check.

I think the green check mark comes from the Waggon. Even if no loco type is selectable in the vehicle database, it has one indeed and this would be the first one from the list.

Regards
Markus

[ebarra]

Dear Markus,
You will find attached my project.
The test line is N°3 in 2R routes Eric01.ZFA under the OR condition.
The loc I am testing is Adress 3998.I have try to change the type of this loco and it works well except with  the Vapeur type which still goes to green.

I removed the loc pictures as it was to heavy.
Thanks.
Regards.

[Markus Herzog]

Hi Eric,

I think I need to change something in the code in 2018.1 for the waggon check, because a waggon has inside (even if not visible) a loco type and I need to block this.
I will try, but I can not promise if it will work.

Regards
Markus

[ebarra]

Markus,
Thanks for the feed-back,
Could another alternative be to extend the option with leading vehicule by being able to check its position:
, 1 vehicule,
in or against driving direction?
 
Regards.
Eric.

[ebarra]

Hello Markus,
Any feed back on this?
Thanks.
Regards.
Eric.

[Markus Herzog]

Hi Eric,

I am sorry, I am completely busy at the moment l

Regards
Markus

[ebarra]

Hi Markus,
I take the oportunity to ask again the status on this one? 
Regards.
Eric.

[Markus Herzog]

Hello Eric,

it is on the list to it for 2018.1, but at the moment other things we started before have to be finished. Please wait until 2018.1 (I can say no release date).

Regards
Markus